Instruction(3G Programmable Flybarless System) :
- 3-axis gyroscopic flybarless system to simulate the stability of mechanical flybar system, yet at the same time achieving agile 3D performance.
- Utilizes Silicon Micro Machine (SMM) sensors for excellent stability.
- 12 bit processors providing ultra high resolution, resulting in highly precise controls
- Software upgradable through PC interface adapter (sold eparately)
- Simplistic setup process without the need of external devices. Setup is done through 5 steps and 2 sensitivity adjustments. Rudder setup is identical to GP780 gyro, minimizing learning curve.
- Flybarless system dramatically improves 3D power output and efficiency, resulting in reduced fuel or electricity consumption.
- Highly sensitive gyroscopic sensors combined with advanced control detection routine providing higher hovering and aerobatic stability than other flybarless system.
- Suitable for all CCPM and mechanical mixing system.
- Comaptible with helicopter of all sizes from T-Rex 250 to T-Rex 700.
- Innovative Pitch Gau as an aid to facilitate pitch adjustments.
- High frame rate signal output for faster and higher precision servo response.
- Capable to operate between 3V to 8.4V, compatible with high voltage servos.
- Small footprint, light weight, minimalists and reliable design.
Specification(3G Programmable Flybarless System) :
-
- Current Comsumption: 80mA @ 4.8V
- Flip and Roll rate detection speed: ±300degrees/sec
- Rudder rate detection speed: ±500degrees/sec
- Sensor resolution: 12bit
- Operating temperatur: -20℃~65℃
- Operating humidity: 0%~95%
- RoHS certified
- Dimension:
Control box: 42x26.5x14.5mm
Sensor: 22.3x21.7x14mm
- Weight:
Control box: 16g
Sensor: 9g
Specification(T-REX 550E) :
- Length: 1042mm
- Height: 364mm
- Main Blade Length: 520mm
- Main Rotor Diameter: 1188mm
- Tail Rotor Diameter: 254mm
- Motor Drive Gear: 16T
- Main Drive Gear: 170T
- Autorotation Tail Drive Gear: 180T
- Tail Drive Gear: 40T
- Drive Gear Ratio: 1:10.62:4.5
- Weight(With Motor): 1800g
- Flying Weight: Approx. 2800g
Features:
- Newly designed aerodynamically efficient metal main blade control system, with high rigidity and superior control precision.
- New lightweight high precision main gear, with excellent balance and stability.
- New lightweight metal main gear hub.
- New lightweight rigid metal main shaft bearing blocks.
- Integrated swash anti-rotation guide and gyro mounting platform.
- Convenient carbon fiber ESC mount for installation either on top of tail boom mount for maximum cooling from main blades, or under rudder servo for maximum flexibility.
- Dual section battery mount for optimal CG position based on battery weight.
- 3K carbon fiber side frame and base plate, simple yet highly rigid for ease of maintenance.
- 600 helicopter grade ψ21.5mm diameter tail boom providing superior rigidity and stability.
- Newly designed rear mounted rudder servo mount, for pleasing aesthetic as well as improving side frame strength and protection to the rudder servo.
- High speed rated thrust bearings in tail blade grips.
- High efficiency torque tube drive.
- High strength carbon fiber used on tail fins and tail boom supports.
- New lightweight landing gears.
- High grade airbrushed fiberglass canopy.
Users must have a certain concept of security to operate the R/C helicopters.
Be sure to read and comply with related safety notes of instruction manual before flying.
Accessories:
- T-REX 550E 3G Kits Set X1
- Aluminum Tail Boom X1
- RCE-BL70G Brushless ESC x1
- 520 Carbon fiber blades X1
- DS610 Digital servo X3 set
- DS620 Digital servo X1
- Flybarless System X1 set
- 600M Brushless Motor X1
- 90mm 3K Carbon Fiber Tail Blades X1 Set
Radio transmitter and electronic equipment required for assembly:
- Transmitter(7-channel or more, helicopter system)
- Receiver(7-channel or more)
- 6S Li-Po 2600 ~ 5200mAh
- Dial Pitch Gauge
|
